Reference: 10HS ECHO - 5Mts
Reference: BASE-U-4
Reference: UA-002-64
Brand: ONSET
Reference: VH400-2M
Brand: VEGETRONIX
Reference: DS1922E-F5
Brand: iBUTTON MAXIM INTEGRATED
PAYMENT METHODS
PFSA D15-R ePTFE Reinforced Proton Exchange Membrane
PFSA D15-R ePTFE Reinforced Proton Exchange Membrane (PEM) is used to separate the anode and cathode compartment of PEM fuel cell stacks that usually consume H2/Air as the fuel/oxidant and requires achieving high current densities (which necessiates the use of a relatively thin membrane). It is quite a common practice in the fuel cell industry to use reinforced or unreinforced PFSA membranes with a thickness of 50 microns or less for most of the commercial applications (such as PEM fuel cells for automotive, heavy duty trucks, buses, etc.). PFSA D15-R ePTFE Reinforced Proton Exchange Membrane has a thickness of 15 microns (+/- 1 microns for the thicknes variation) and ideally suited for PEM fuel cell stacks that would yield very high current densities and long operational lifetimes. The mechanical reinforcement in this membrane is based on the microporous ePTFE which has 3-D porous regions where the ionically conducting PFSA is wet impregnated via solution cast method. This material has a backing plastic on one side.
D15-R expands the possibility of finding an excellent fit for your requirements, without diminishing the worth of Nafion HP.
The major benefit of mechanically reinforced PFSA membranes would be their significantly enhanced operational lifetime compared to the unreinforced PFSA membranes due to swelling related stresses being taken up by the ePTFE reinforcement. One of the major limitations of the mechanically reinforced PFSA membranes is their lower proton or ionic conductivity compared to unreinforced membranes because of less ionically conducting material per unit volume or per unit mass (while ePTFE reinforcement is quite porous, it does have a mass regardless). While it is not a common practice, this membrane product can also be used in PEM water electrolyzer, direct methanol fuel cells (DMFCs), direct formic acid fuel cells (DFAFC), microbial fuel cells (MFC) and other similar applications and it is always advised that the end-user to take into consideration of the thickness of the PFSA membrane for their particular application and how it may effect the performance positively or negatively.
PFSA D15-R ePTFE Reinforced Proton Exchange Membrane is based on the chemically stabilized perfluorosulfonic acid material and it is shipped in the acid (H+) form (which is also known as protonic form). Chemical stabilization is also known as end-group stabilization where the carbon atoms that end of the PFSA polymer chains are fully fluorinated. Chemically stabilized PFSA membranes will exhibit substantially lower fluoride ion release compared to the PFSA membranes manufactured from unstabilized PFSA resin. Functional groups (also known as sulfonic acid sites) for this PFSA membrane are based on the long side chain for its chemical structure.
Proton exchange membranes are also known as cation exchange membranes in the market. This PFSA membrane performs as a separator and solid electrolyte (without the need of a liquid acid) in a variety of electrochemical cells that require the membrane to selectively transport protons or other various cations across the cell junction (or between anode and cathode catalyst layers). The polymer is chemically resistant and durable.
Membrane Properties
| Thickness | 15 micrometers (+/- 1 micrometers) |
| Basic Weight (g/m²) | TBD |
| Conductivity (S/cm) | ≥ 0.03 S/cm (or ≥ 30 mS/cm) |
| Ion Exchange Capacity | ≥ 1.00 mmol/g |
| Swelling (%) | ≤ 7.5% / 7.5% (MD/TD) |
| Modulus (MPa) | Elastic Modulus ≥ 250 MPa / 250 MPa (MD/TD) |
| Tensile Strength - max. (MPa) | ≥ 25 / 25 MPa (MD/TD) |
| Elongation to Break (%) | 250% for MD and 260% for TD |
| Membrane Hydrolytic Properties | |
| Water content (% water) | TBD |
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: 57080205 1gr
Brand: FUEL CELL
Reference: 12120003
Brand: FUEL CELL
Reference: 12120018
Brand: FUEL CELL
Reference: 12120030
Brand: FUEL CELL
Reference: 12120023
Brand: FUEL CELL
Reference: 12120008
Brand: FUEL CELL
Reference: 67130012
Brand: FUEL CELL
Reference: 11060016
Brand: FUEL CELL
Reference: 12120020
Brand: FUEL CELL
Reference: 12120036
Brand: FUEL CELL
Reference: 57080182 1gr
Brand: FUEL CELL
Reference: 12120016
Brand: FUEL CELL
Reference: 57080103
Brand: FUEL CELL
Reference: 12120027
Brand: FUEL CELL
Reference: 12120044
Brand: FUEL CELL
Reference: 12120022
Brand: FUEL CELL
PFSA D15-R ePTFE Reinforced Proton Exchange Membrane
PFSA D15-R ePTFE Reinforced Proton Exchange Membrane (PEM) is used to separate the anode and cathode compartment of PEM fuel cell stacks that usually consume H2/Air as the fuel/oxidant and requires achieving high current densities (which necessiates the use of a relatively thin membrane). It is quite a common practice in the fuel cell industry to use reinforced or unreinforced PFSA membranes with a thickness of 50 microns or less for most of the commercial applications (such as PEM fuel cells for automotive, heavy duty trucks, buses, etc.). PFSA D15-R ePTFE Reinforced Proton Exchange Membrane has a thickness of 15 microns (+/- 1 microns for the thicknes variation) and ideally suited for PEM fuel cell stacks that would yield very high current densities and long operational lifetimes. The mechanical reinforcement in this membrane is based on the microporous ePTFE which has 3-D porous regions where the ionically conducting PFSA is wet impregnated via solution cast method. This material has a backing plastic on one side.
D15-R expands the possibility of finding an excellent fit for your requirements, without diminishing the worth of Nafion HP.
check_circle
check_circle
