Reference: 10HS ECHO - 5Mts
Reference: 10HS ECHO - 5Mts
Reference: BASE-U-4
Reference: UA-002-64
Brand: ONSET
Reference: DS1922E-F5
Brand: iBUTTON MAXIM INTEGRATED
Reference: DS9107+
Brand: iBUTTON MAXIM INTEGRATED
LAQUAtwin Ca‐11C‐1 LAQUAtwin iCa Checker Calcium Ionometer
It is a calcium meter used to measure hypocalcemia in bovine blood. It measures calcium reliably and is very easy to use. It only takes a few minutes to give a result, making it an ideal instrument to know the health status of your cow.
Specifications:
Range: 0.1 to 5.0 mmol/L.
Resolution: 0.1 mmol/L.
Accuracy: ± 20% of reading value.
Calibration: 2 points.
Standard solution 1.25 mmol/L
Standard solution 2.50 mmol/L
The wide measuring range (0.1 to 5.0 mmol/L) allows high concentrations to be measured without the need for dilution.
Uses:
- Evaluation of the calcium content in the blood of dairy cows.
This equipment incorporates a flat ion-selective electrode for microvolume measurement. The replaceable electrode uses the same measuring principle as the traditional calcium ion-selective electrode (ISE). It only requires a few drops (0.3 ml) to provide a fast and accurate analysis.
Main features:
Temperature compensation.
Automatic calibration: recognizes calibration solutions. The user can choose calibrations at one or two points.
Detection of result stability.
Waterproof (IP67).
No reagents used.
Automatic selection of the appropriate range.
Automatic shutdown (30 minutes).
Measurement in three simple steps:
1. Calibration: For a correct calibration, the sensor must be clean beforehand. If not, rinse with cleaning solution and put some standard solution on the sensor and press the calibration button. A smiley face will appear indicating that calibration is complete. Wipe the sensor with cleaning solution until the calibration solution is removed and dry it with a soft, clean tissue.
2. Analysis: Only a tiny amount of sample is required, so just fill the sensor and wait a few seconds until the smiley face appears.
3. Cleaning: Always keep the sensor clean.
Sensors should be replaced after approximately 1000 measurements or when calibration cannot be performed. Sensors are sold separately and can be easily removed and replaced.
This calcium meter comes in two formats:
OPTION A
2 CR2032 batteries, 1 wash bottle, Instruction Manual and Quick Start Guide.
Storage case.
1 Calibration solution at 1.25 mmol/L (25 ml).
1 2.50 mmol/L calibration solution (25 ml).
1 Cleaning solution (250 ml).
OPTION B
2 CR2032 batteries, 1 wash bottle, Instruction manual and Quick guide.
Storage case.
2 1.25 mmol/L calibration solution (25 ml).
2 2.50 mmol/L calibration solution (25 ml).
3 Cleaning solution (250 ml).
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Reference: PX3DXX02S
Brand: VERIS
Reference: UR Sensor
Brand: NESA
Reference: Affinity Gateway
Reference: RK300-06B
Brand: RIKA SENSORS
Reference: 12120045
Brand: FUEL CELL
Reference: PP-100
Brand: Apogee Instruments
Reference: CRONOSONIC
Brand: MAE
Reference: S080‐ORP
Brand: HORIBA LAQUAtwin
Reference: DD-L1
Brand: ECOMATIK
Reference: LS195
Brand: LINSHANG
Reference: ME131M
Brand: Meatrol
Reference: M1300
Brand: COMET
Reference: MX2301A
Brand: ONSET
check_circle
check_circle